DIY_EFI Digest Sunday, August 8 1999 Volume 04 : Number 456 In this issue: Re: Message from CSH, HQ Re: DIY_EFI Digest V4 #455 Looking for ALDL connectors See the end of the digest for information on subscribing to the DIY_EFI or DIY_EFI-Digest mailing lists. ---------------------------------------------------------------------- Date: Sat, 07 Aug 1999 13:09:57 -0700 From: garfield@xxx.com (Gar Willis) Subject: Re: Message from CSH, HQ On Sat, 7 Aug 1999 13:03:54 -0500 nacelp@xxx.com (CSH-HQ) wrote: >Well, hope ya enjoyed the holidays, the dwarfs have been recalled to duty so, >here we go, >again thanks Gar, for the up date. Pardon my tardiness, but only email so >far, working on archives next. Twern't no fun atoll, look wha happened; you leave on 'vacation' (sic), and immediately the list gets ingested and 'digested'. Welcome back, O Conical One. Gar ------------------------------ Date: Sat, 7 Aug 1999 16:57:26 -0500 From: nacelp@xxx.com (CSH-HQ) Subject: Re: DIY_EFI Digest V4 #455 Several of the new Hot ROd mags have had ads for varous ones. Bruce >Date: Sat, 7 Aug 1999 09:18:35 EDT >From: Chipsbyal@xxx.com >Subject: 4L60-E Aftermarket controller > >Hope this helps. I found this company in Transmission Digest magazine. They >have a product called ePlace Retrofit. Check out there Web page >www.autotransinc.com >or call 1.888.453.3767. There are quite a few other useful products on their >page. > >------------------------------ > >Date: Fri, 06 Aug 1999 23:01:49 -0600 >From: "David C. Allen" >Subject: TPI into a 86 4x4 Suburban PART 2 Long > >Fourth Question: >Chevy uses a o-ring, Saginaw flare to connect the high pressure fuel lines, >and I was wondering if anyone knows who or where one can get steel tubing >flared. >Power steering hoses use this type of flare. Just use Earls'/Russell's stuff in a long run not that much more, and after you study the stock routing you'll see it's shortcomings. > >Again if this is not the proper forum please let me know > >Thanks > >David > >------------------------------ > >Date: Sat, 7 Aug 1999 10:10:21 -0700 >From: "Marvin Johnson" >Subject: New list member, TBI question. > >Hi, > I recently purchased the computer harness etc for an 88 Astro van 4.3 >with the intent of putting it on my Jeep 258. I understand the process of >retro fitting the TBI. However, I have come into possession of the EFI >manifold and injectors for a 4.0 jeep motor, but I don't have the computer >or associated parts. Is it possible to drive the six injectors with the TBI >computer? I understand I would have to fire the injectors in two groups. How >would I wire this, injectors in series, parallel, or is it more complex than >this? For a first attenpt make up yor mind which system to use, hybredding can get to be a real pain. I'd recomment doing the tbi, and then maybe think of the port type. Hope that was a 1227747 ecm, since that is hacked. Bruce > Any help is appreciated. > > > >Marvin Johnson > > > >Spokane Washington > >------------------------------ > >Date: Sat, 7 Aug 1999 13:03:54 -0500 >From: nacelp@xxx.com (CSH-HQ) >Subject: Message from CSH, HQ > >Well, hope ya enjoyed the holidays, the dwarfs have been recalled to duty so, >here we go, >again thanks Gar, for the up date. Pardon my tardiness, but only email so >far, working on archives next. >Cheers >Bruce > >------------------------------ > >End of DIY_EFI Digest V4 #455 >***************************** > >To subscribe to DIY_EFI-Digest, send the command: > > subscribe diy_efi-digest > >in the body of a message to "Majordomo@xxx. > >A non-digest (direct mail) version of this list is also available; to >subscribe to that instead, replace "diy_efi-digest" in the command > above with "diy_efi". > ------------------------------ Date: Sat, 7 Aug 1999 19:58:45 EDT From: Mikepoore@xxx.com Subject: Looking for ALDL connectors Does anyone know where I can find 12 pin and 16 pin GM ALDL connectors? I am looking for the male ends. I've got my interface working, but I would like to connect and disconnect it a little easier than pin by pin. Mike Poore ------------------------------ End of DIY_EFI Digest V4 #456 ***************************** To subscribe to DIY_EFI-Digest, send the command: subscribe diy_efi-digest in the body of a message to "Majordomo@xxx. A non-digest (direct mail) version of this list is also available; to subscribe to that instead, replace "diy_efi-digest" in the command above with "diy_efi".