DIY_EFI Digest Wednesday, January 19 2000 Volume 05 : Number 030 In this issue: Re: DIY_EFI Digest V5 #29 See the end of the digest for information on subscribing to the DIY_EFI or DIY_EFI-Digest mailing lists. ---------------------------------------------------------------------- Date: Wed, 19 Jan 2000 20:46:21 +0100 From: "Torstein Moshuus" Subject: Re: DIY_EFI Digest V5 #29 - ----- Original Message ----- From: DIY_EFI Digest To: Sent: Wednesday, January 19, 2000 11:00 AM Subject: DIY_EFI Digest V5 #29 > > DIY_EFI Digest Wednesday, January 19 2000 Volume 05 : Number 029 > > > > In this issue: > > Re: Lamda sensor mounting > RE: Lambda sensor mounting > Re: DIY_EFI Digest V5 #27 > Leaded EGO sensor > Re: Leaded EGO sensor > Re: lamda sensors > > See the end of the digest for information on subscribing to the > DIY_EFI or DIY_EFI-Digest mailing lists. > > ---------------------------------------------------------------------- > > Date: Tue, 18 Jan 2000 20:00:39 -0000 > From: "Gareth Jones" > Subject: Re: Lamda sensor mounting > > > Hi, > > > > I am running a Mini with a highly tuned A series engine (100bhp from a > > 1.3litre). It has a carb and Distributer but I am thinking about adding a > > Lamda sensor with a dash mounted gauge so that I can Keep an eye on the > > mixture. > > > > Where in the exhaust system is the best place to mount the sensor? Close > to > > the head? 6ft down the exhaust? I have a Long center branch exhaust > > manifold which doesn't bring the ports together for about 3ft after the > > cylinder head. The manifold is also new (and expensive) so I would prefur > > to mount is in the exhaust if it doesn't affect the reading. > > > > I plan to get a sensor from a car in a scrap yard are there any UK (comon) > > makes of cars that have better Lamda sensor than others? > > > > In the UK they recently banned Leaded petrol. They made Lead replacement > > petrol available to 'replace' it. Does LRP clog lamba sensors like Leaded > > petrol does? I can run Unleaded but LRP has Higher Octane rating than > > Unleaded and is cheaper than Super Unleaded. > > > > Thanks, > > > > Ade > > > > > > Hi Ade, > > I had a mini catalogue a while ago which listed an LCB Y peice with a boss > for mounting a lambda sensor. Unfortunately I can't find the catalogue > anymore, but I would suggest you try the usual big suppliers MiniSpares, > MiniSport, MiniSpeed, etc. I bet you non mini owners just can't believe the > cunning originality in these names ;-) Or maybe even try going directly to > somebody like Maniflow. Either way it would be cheaper than wrecking a whole > LCB. > > Gareth Jones > > ------------------------------ > > Date: Tue, 18 Jan 2000 21:18:58 -0000 > From: "Rich M" > Subject: RE: Lambda sensor mounting > > Ade, > I've no experience with minis but I have done the same as you propose with a > 2.0 pinto engined Escort and 1.8i Vauxhall Cavalier. I mounted in both cases > at the end of the manifold/downpipe (below floor level, using a heated Bosch > 4-wire sensor. With the heater powered, the sensor operates right down to > idle, with the heater off, the sensor doesn't stay hot enough at idle but is > fine under driving conditions. The sensor I used was ex. Rover, and is the > same one used throughout the range of 'K' series engines and 'T'/'M' series. > (ie, 200's, 400's, 600T, 800 4-cyl.). Vauxhall use a very similar sensor on > Motronic (Bosch multipoint) systems; TBi (Multec) applications use a single > wire unheated Rochester sensor which needs to be close to the engine to work > properly. > Hope this helps. > > Rich. > > > Date: Sun, 16 Jan 2000 14:47:33 +0000 > > From: Ade + Lamb Chop > > Subject: Lamda sensor mounting > > > > Hi, > > > > I am running a Mini with a highly tuned A series engine (100bhp from a > > 1.3litre). It has a carb and Distributer but I am thinking about adding a > > Lamda sensor with a dash mounted gauge so that I can Keep an eye on the > > mixture. > > > > Where in the exhaust system is the best place to mount the > > sensor? Close to > > the head? 6ft down the exhaust? I have a Long center branch exhaust > > manifold which doesn't bring the ports together for about 3ft after the > > cylinder head. The manifold is also new (and expensive) so I would prefur > > to mount is in the exhaust if it doesn't affect the reading. > > > > I plan to get a sensor from a car in a scrap yard are there any UK (comon) > > makes of cars that have better Lamda sensor than others? > > > > In the UK they recently banned Leaded petrol. They made Lead replacement > > petrol available to 'replace' it. Does LRP clog lamba sensors like Leaded > > petrol does? I can run Unleaded but LRP has Higher Octane rating than > > Unleaded and is cheaper than Super Unleaded. > > > > Thanks, > > > > Ade > From: Torstein Moshuus 19.Feb.00 tmoshuus@xxx.no Re: Location of lambda sensor The sensor should be as close to the the exhaust outlet as possible. In case of Alīs Mini I would suspect that he should locate the adaptor as close to the end of the manifold as possible. The sensor does not give reliable readings unless heated to approx. 600 degrees (F). A heated sensor would be less dependent on temperature (of course). Incidentally what kind of instrument are you using in order to measure the very low voltages we are dealing with here ( less than 1 volt and a pretty high impedance looking into the sensor) ? rgrds > ------------------------------ > > End of DIY_EFI Digest V5 #29 > **************************** > > To subscribe to DIY_EFI-Digest, send the command: > > subscribe diy_efi-digest > > in the body of a message to "Majordomo@xxx. > > A non-digest (direct mail) version of this list is also available; to > subscribe to that instead, replace "diy_efi-digest" in the command > above with "diy_efi". ------------------------------ End of DIY_EFI Digest V5 #30 **************************** To subscribe to DIY_EFI-Digest, send the command: subscribe diy_efi-digest in the body of a message to "Majordomo@xxx. A non-digest (direct mail) version of this list is also available; to subscribe to that instead, replace "diy_efi-digest" in the command above with "diy_efi".