From: sfahey@unicom.net Subject: Apple ][ Parallel Interface Card Specs Date: Wed, 14 Jan 1998 05:22:22 -0600 Message-ID: <884625835.1659830277@dejanews.com> Newsgroups: comp.sys.apple2 Organization: Deja News Posting Service Path: news1.icaen!news.uiowa.edu!news1.chicago.iagnet.net!iagnet.net!nntp.texas.net!nntp2.dejanews.com!grunt.dejanews.com!not-for-mail X-Article-Creation-Date: Mon Jan 12 17:23:58 1998 GMT X-Authenticated-Sender: sfahey@unicom.net X-Http-User-Agent: Mozilla/4.04 [en] (Win95; I) X-Originating-IP-Addr: 206.113.121.61 (dial-277.access.unicom.net) Lines: 174 Xref: news1.icaen comp.sys.apple2:129165 DB-25 Connector Pinout ---------------------- DB-25 Connector Signal Name 1..............Data In, Bit 0 2..............Signal Ground 3..............Data In, Bit 2 4..............Signal Ground 5..............Data Out, Bit 0 6..............Data Out, Bit 1 7..............Blocked 8..............Data Out, Bit 2 11..............Data Out, Bit 5 12..............Data Out, Bit 6 13..............Data Out, Bit 7 14..............Data In, Bit 4 15..............Strobe Out 16..............Acknowledge In 17..............Data In, Bit 1 18..............Data In, Bit 7 19..............Data In, Bit 5 20..............Signal Ground 21..............Data In, Bit 6 22..............Data Out, Bit 3 23..............Data Out, Bit 4 24..............Signal Ground 25..............Data In, Bit 3 Switch Settings =============== Strobe Length ------------- 1 microsecond -> SW1-1:Off, SW1-2:Off, SW1-3:Off 3 microseconds -> SW1-1:On, SW1-2:Off, SW1-3:Off 5 microseconds -> SW1-1:Off, SW1-2:On, SW1-3:Off 7 microseconds -> SW1-1:On, SW1-2:On, SW1-3:Off 9 microseconds -> SW1-1:Off, SW1-2:Off, SW1-3:On 11 microseconds -> SW1-1:On, SW1-2:Off, SW1-3:On 13 microseconds -> SW1-1:Off, SW1-2:On, SW1-3:On 15 microseconds -> SW1-1:On, SW1-2:On, SW1-3:On Strobe Polarity --------------- Positive -> SW1-4:Off Negative -> SW1-4:On Ack Polarity ------------ Positive -> SW1-5:Off Negative -> SW1-5:On Firmware Select --------------- Parallel (LF) -> SW1-6:Off Centronics (No LF) -> SW1-6:On Interrupts ---------- Disable -> SW1-7:Off Enable -> SW1-7:On Interrupts should be enabled for the Apple III and disabled for the Apple II. Switch Setting Explanations --------------------------- Different peripherals (non-Apple printers, etc.) may use I/O signals that have different duration and polarity. The STROBE LENGTH, STROBE POLARITY, and ACK POLARITY switch settings on the Parallel Interface Card (2PIC) give you the flexibility to communicate with these other devices. For the I/O signal characteristics of the device you are connecting with, read its manual. Controlling Bit 8 ----------------- The following program enables you to control bit 8, used by some printers to select expanded or normal print mode or to enable alternate or graphics character sets. DOS 3.2 or DOS 3.3 is required to use this routine, which also works in the Apple III in Emulation mode. Determine which slot your interface card is in and the corresponding slot code from the table. Replace "" with the slot number and "" with the code when typing in the program. slot 1 2 3 4 5 6 7 code C1 C2 C3 C4 C5 C6 C7 Enter the monitor with Call -155 and type: 3B0:A9 :20 95 FE :A9 80 :20 ED FD :A9 C5 :85 36 :A9 03 :85 37 :4C EA 03 :29 7F :0D CD 03 :4C 02 :80 To check your typing, type: 3B0L Compare your listing to the one below configured for slot 1. 03B0- A9 01 LDA #$01 03B2- 20 95 FE JSR $FE95 03B5- A9 80 LDA #$80 03B7- 20 ED FD JSR $FDED 03BA- A9 C5 LDA #$C5 03BC- 85 36 STA $36 03BE- A9 03 LDA #$03 03C0- 85 37 STA $37 03C2- 4C EA 03 JMP $03EA 03C5- 29 7F AND #$7F 03C7- 0D CD 03 ORA $03CD 03CA- 4C 02 C1 JMP $C102 03CD- 80 ??? Enter 3D0G to return to Basic. Save the driver to disk by typing: BSAVE CEN 730, A$3B0, L$1E Load the driver and initialize the interface before using the printer. From command mode, type: BLOAD CEN 730 Call 944 Or from a program: 100 Print D$;"BLOAD CEN 730" : Call 944, assuming that D$ is a CTRL-D. To switch back to the video monitor for output type: PR#0 or in a program enter: 200 Print D$;"PR#0" To reconnect the printer, all that is required is: Call 954, or from a program: 300 Call 954 To set normal print mode, type POKE 973,0; type POKE 973,128 to set the expanded print mode POKE. Cable Pinouts ------------- Here is a sample pinout for an Apple II parallel card to a parallel printer. 20-Pin Amphenol DIL Connector Connector (Female) (Male) 1 ---------- 14 2 ---------- 10 8 ---------- 1 10 ---------- 2 11 ---------- 3 12 ---------- 4 13 ---------- 5 14 ---------- 6 15 ---------- 7 16 ---------- 8 17 ---------- 9 20 ---------- 16 -------------------==== Posted via Deja News ====----------------------- http://www.dejanews.com/ Search, Read, Post to Usenet