============================= MC68HC05T2 ================ rev 04/13/94 *** CUSTOMER XC STATUS LETTER REQUIRED *** MOTOROLA CSIC MCU DIVISION ORDER FORM ------------------------------------------------------------------------ Use this form when submitting code on diskettes. ------------------------------------------------------------------------ This form is subject to change. Check with your Motorola salesperson or marketer to make sure you have a current form. This form must be filled out completely before code is submitted. Contact your Motorola salesperson for assistance. DO NOT CHANGE THE OPTIONS LISTED ON THIS FORM. IF REQUIRED OPTIONS ARE NOT LISTED, INCLUDE THE INFORMATION IN THE COMMENTS/SPECIAL ELECTRICAL SECTION. ------------------------------------------------------------------------ Motorola SC Number (if pre-assigned):_____________________Date:_________ Customer:_______________________________________________________________ Street Address(No P.O. Boxes):__________________________________________ City:_______________________________________State:______________________ Zip Code:__________________Country:_____________________________________ Customer Contact:_______________________________________________________ Phone #: (_______)______________________Extension #:____________________ Salesperson:____________________________________________________________ Sales Office:___________________________Phone #: (_______)______________ Customer Part Number:___________________________________________________ _____________________________ Customer part #, if part of marking, is (signature) for reference only. There is either no print, or print is tested to Motorola or data sheet electrical information. _____________________________ There is a print/spec for this device (signature) and ordered parts must comply to this spec as it deviates from Motorola standard. (PRINT/SPEC MUST BE SUBMITTED WITH THIS ORDER FORM.) ------------------------------------------------------------------------ Encryption/Decryption Algorithm included in customer software or end use application (if encryption/decryption algorithm is included, contact your Motorola salesperson BEFORE SUBMITTING CODE, additional information is required): ___ YES ___ NO MCU Function and Customer End Use Description:__________________________ ________________________________________________________________________ ________________________________________________________________________ MCU Function and Customer End Use Description examples: Encryption controller for secured serial port for a personal computer. Motor controller for automatic focus on a consumer camera. Main controller for remote controller for entertainment systems. Speech chip controller for voice synthesizer for a commercial automobile cruise control. End Use ECCN:___________________________________________________________ Military Application: ___ YES ___ NO ------------------------------------------------------------------------ PATTERN SUBMISSION: The original customer diskette will be kept by Motorola for contractual purposes. Label the diskette with customer name, date, MCU ROM device and SC number (if pre-assigned). Use Motorola S19 EXORciser format. NON-USER AREAS MUST BE LEFT BLANK OR FILLED WITH ZEROES. Motorola may request pattern resubmission if non-user areas contain any non-zero code. CHOOSE ONLY ONE: ___ 3.5" diskette Macintosh format: ___ 1.4M DS HD ___ 800K DS DD ___ 3.5" diskette IBM format: ___ 1.44M DS HD ___ 720K DS DD ___ 5.25" diskette IBM format: ___ 1.2M DS HD ___ 360K DS DD Motorola will send the customer a copy of the verify listing on a CUSTOMER SUPPLIED diskette (must be the same type of diskette as the pattern submission diskette). This is in addition to a hard copy printout of the verify listing. ------------------------------------------------------------------------ MOTOROLA TO SHIP VERIFY LISTING TO: ___ Customer at above address (No P.O. Boxes - addresses in U.S. only) ___ Motorola sales office RVUS WILL BE SENT TO THE MOTOROLA SALES OFFICE. In the U.S., RVUs will be shipped direct to the customer if a factory order has been set up for shipment to the customer. ------------------------------------------------------------------------ Is this pattern an updated version of an existing ROM code? ___ YES ___ NO If yes, what is the existing SC number? _____________ Where will this pattern be mass produced? ___ U.S. ___ Israel ___ Europe ___ Japan ___ Asia Pacific ___ Other, please specify ____________ Have you asked your Motorola representative if an errata sheet exists for this device? ___ YES ___ NO ------------------------------------------------------------------------ Comments/Special Electrical Provisions****/Preferred Maskset****: **** requires prior factory approval ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ------------------------------------------------------------------------ User on-screen display (OSD) ROM area: $0400 to $07FF (.OSD) User ROM area: $0400 to $3EFF (.DAT) User Vectors: $3FF6 to $3FFF (.DAT) Address area $0400 to $07FF is used twice. The user OSD ROM must be submitted in one file starting at location $0400. The user ROM & vectors must be submitted in another file starting at location $0400. DIGITAL TO ANALOG CONVERTER DA0 THRU DA8 (PORT B & PIN PC0): ___ open drain for internal use only: ___ TTL check PI sheet INTERNAL OSCILLATOR INPUT: ___ crystal/ceramic resonator (Option XL) EXTERNAL INTERRUPT TRIGGER: ___ edge-sensitive only (Option IA) ___ level- and edge-sensitive (Option IB) COMPUTER OPERATING PROPERLY (COP) WATCHDOG TIMER: ___ enable (Option EC) ___ disable (Option DC) HALF TONE PIN: ___ active low (Option HL) ___ active high (Option HH) FAST BLANKING PIN: ___ active low (Option FL) ___ active high (Option FH) SERIAL I/O PORT (SIOP) DATA FORMAT: ___ most significant bit first (Option MB) ___ least significant bit first (Option LB) VERTICAL DELAY: ___ +8 (Option V2 V4) ___ 0 (Option V2 V3) ___ -8 (Option V1 V4) ___ -16 (Option V1 V3) EXTERNAL OSCILLATOR FREQUENCY (4.0 MHz maximum): _________________________ TEMPERATURE RANGE: 0 to 70 degrees C PRODUCTION PACKAGE TYPE: ___ 40 pin plastic DIP (P) ___ 44 pin PLCC (FN) requires prior factory approval ___ 42 pin plastic shrink DIP (B) RVU SAMPLE PACKAGE TYPE: ___ ceramic equivalent of 40 pin plastic DIP (P) ___ ceramic equivalent of 42 pin plastic shrink DIP (B) requires prior factory approval ___ none (no RVUs to be sent to customer/ship to production orders only) MARKING ON PACKAGED PRODUCTION MCUS: ___ standard Motorola marking: DIP: line 1: Motorola Logo Motorola SC number line 2: 5 character Motorola mask set line 3: Motorola traceability code PLCC: line 1: Motorola Logo line 2: Motorola SC number line 3: 5 character Motorola mask set line 4: Motorola traceability code ___ customer marking in addition to the standard Motorola marking: _________________________ maximum: 14 characters per line 2 customer lines * _________________________ * The Motorola SC number will not appear on the package if all additional customer lines are used. Marking the packages with the Motorola SC number will facilitate the manufacturing process. The Motorola Logo and copyright symbol use 2 characters each. DIP marking maximum: total of 4 lines, 14 characters per line. PLCC marking maximum: total of 5 lines, 14 characters per line. ============================= MC68HC05T2 ================ rev 04/13/94