============================== MC6805R2 ================= rev 04/13/94 MOTOROLA CSIC MCU DIVISION ORDER FORM ------------------------------------------------------------------------ Use this form when submitting code on diskettes. ------------------------------------------------------------------------ This form is subject to change. Check with your Motorola salesperson or marketer to make sure you have a current form. This form must be filled out completely before code is submitted. Contact your Motorola salesperson for assistance. DO NOT CHANGE THE OPTIONS LISTED ON THIS FORM. IF REQUIRED OPTIONS ARE NOT LISTED, INCLUDE THE INFORMATION IN THE COMMENTS/SPECIAL ELECTRICAL SECTION. ------------------------------------------------------------------------ Motorola SC Number (if pre-assigned):_____________________Date:_________ Customer:_______________________________________________________________ Street Address(No P.O. Boxes):__________________________________________ City:_______________________________________State:______________________ Zip Code:__________________Country:_____________________________________ Customer Contact:_______________________________________________________ Phone #: (_______)______________________Extension #:____________________ Salesperson:____________________________________________________________ Sales Office:___________________________Phone #: (_______)______________ Customer Part Number:___________________________________________________ _____________________________ Customer part #, if part of marking, is (signature) for reference only. There is either no print, or print is tested to Motorola or data sheet electrical information. _____________________________ There is a print/spec for this device (signature) and ordered parts must comply to this spec as it deviates from Motorola standard. (PRINT/SPEC MUST BE SUBMITTED WITH THIS ORDER FORM.) ------------------------------------------------------------------------ Encryption/Decryption Algorithm included in customer software or end use application (if encryption/decryption algorithm is included, contact your Motorola salesperson BEFORE SUBMITTING CODE, additional information is required): ___ YES ___ NO MCU Function and Customer End Use Description:__________________________ ________________________________________________________________________ ________________________________________________________________________ MCU Function and Customer End Use Description examples: Encryption controller for secured serial port for a personal computer. Motor controller for automatic focus on a consumer camera. Main controller for remote controller for entertainment systems. Speech chip controller for voice synthesizer for a commercial automobile cruise control. End Use ECCN:___________________________________________________________ Military Application: ___ YES ___ NO ------------------------------------------------------------------------ PATTERN SUBMISSION: The original customer diskette will be kept by Motorola for contractual purposes. Label the diskette with customer name, date, MCU ROM device and SC number (if pre-assigned). Use Motorola S19 EXORciser format. NON-USER AREAS MUST BE LEFT BLANK OR FILLED WITH ZEROES. Motorola may request pattern resubmission if non-user areas contain any non-zero code. CHOOSE ONLY ONE: ___ 3.5" diskette Macintosh format: ___ 1.4M DS HD ___ 800K DS DD ___ 3.5" diskette IBM format: ___ 1.44M DS HD ___ 720K DS DD ___ 5.25" diskette IBM format: ___ 1.2M DS HD ___ 360K DS DD Motorola will send the customer a copy of the verify listing on a CUSTOMER SUPPLIED diskette (must be the same type of diskette as the pattern submission diskette). This is in addition to a hard copy printout of the verify listing. ------------------------------------------------------------------------ MOTOROLA TO SHIP VERIFY LISTING TO: ___ Customer at above address (No P.O. Boxes - addresses in U.S. only) ___ Motorola sales office RVUS WILL BE SENT TO THE MOTOROLA SALES OFFICE. In the U.S., RVUs will be shipped direct to the customer if a factory order has been set up for shipment to the customer. ------------------------------------------------------------------------ Is this pattern an updated version of an existing ROM code? ___ YES ___ NO If yes, what is the existing SC number? _____________ Where will this pattern be mass produced? ___ U.S. ___ Israel ___ Europe ___ Japan ___ Asia Pacific ___ Other, please specify ____________ Have you asked your Motorola representative if an errata sheet exists for this device? ___ YES ___ NO ------------------------------------------------------------------------ Comments/Special Electrical Provisions****/Preferred Maskset****: **** requires prior factory approval ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ ------------------------------------------------------------------------ User ROM Areas: $0080 to $00FF, $07C0 to $0F37 User Vectors: $0FF8 to $0FFF The submitted pattern (user ROM & vectors) must begin at location $0080. INTERNAL OSCILLATOR INPUT: ___ crystal/ceramic resonator (Option XL) ___ resistor capacitor (Option RC) TIMER CLOCK SOURCE: ___ internal 02 clock (default) ___ timer input pin (Option EC) TIMER PRESCALER: ___ divide by 1 (Option P0) ___ divide by 2 (Option P1) ___ divide by 4 (Option P2) ___ divide by 8 (Option P3) ___ divide by 16 (Option P4) ___ divide by 32 (Option P5) ___ divide by 64 (Option P6) ___ divide by 128 (Option P7) LOW VOLTAGE INHIBIT: ___ enable (default) ___ disable (Option KL) PORT A: ___ CMOS & TTL (Option UA) ___ TTL only (default) PORT C: ___ TTL only (default) ___ open drain (Option OC) EXTERNAL OSCILLATOR FREQUENCY (0.4 MHz minimum to 4.2 MHz maximum): _________________________ TEMPERATURE RANGE: ___ 0 to 70 degrees C ___ -40 to +85 degrees C /C/ (Option ET) PRODUCTION PACKAGE TYPE: ___ 40 pin plastic DIP (P) ___ 44 pin PLCC (FN) ___ 44 pin PLCC tape & reel (FNR2) RVU SAMPLE PACKAGE TYPE (choose only one): ___ 40 pin ceramic equivalent of plastic DIP (P) ___ 44 pin ceramic equivalent of PLCC (FN) ___ none (no RVUs to be sent to customer/ship to production orders only) MARKING ON PACKAGED PRODUCTION MCUS: ___ standard Motorola marking: DIP: line 1: Motorola Logo Motorola SC number line 2: 5 character Motorola mask set line 3: Motorola traceability code PLCC: line 1: Motorola Logo line 2: Motorola SC number line 3: 5 character Motorola mask set line 4: Motorola traceability code ___ customer marking in addition to the standard Motorola marking: _________________________ maximum: 14 characters per line 2 customer lines * _________________________ * The Motorola SC number will not appear on the package if all additional customer lines are used. Marking the packages with the Motorola SC number will facilitate the manufacturing process. The Motorola Logo and copyright symbol use 2 characters each. DIP marking maximum: total of 4 lines, 14 characters per line. PLCC marking maximum: total of 5 lines, 14 characters per line. ============================== MC6805R2 ================= rev 04/13/94